PWA 4: New Origins...

[Dznts]

Originally Posted by jewel25

Awesome. I wish I had the skill to do that. Or the fact that I get bored too easily to do it.

i am hoping that it doesnt require to much skill, the instructions seem to be well detailed which will really help.

Originally Posted by PoorMansCamaro

if we had the space, and tools, i would tackle the install myself.

it should be interesting to say the least. i may start tearing the engine apart next weekend.

[Dznts]

Originally Posted by Pamela578

Party time

[jewel25]

Told you is was pretty

[PoorMansCamaro]

Originally Posted by Dznts

i am hoping that it doesnt require to much skill, the instructions seem to be well detailed which will really help.

it should be interesting to say the least. i may start tearing the engine apart next weekend.

is the camaro your daily driver?

[SinisterEcho]

Originally Posted by Dznts

i am hoping that it doesnt require to much skill, the instructions seem to be well detailed which will really help.

it should be interesting to say the least. i may start tearing the engine apart next weekend.

It is a blast to do! If i can do it, im sure you will be just fine. Do you have to "pin the crank"?



Herro everyone!

[Dznts]

Originally Posted by PoorMansCamaro

is the camaro your daily driver?

no sir. its my barely driven car..lol

[Dznts]

Originally Posted by SinisterEcho

It is a blast to do! If i can do it, im sure you will be just fine. Do you have to "pin the crank"?



Herro everyone!

yah gotta pin the crank, which i hear is the worst part.

[jewel25]

Access is kicking my butt this morning. But I won

[SinisterEcho]

Originally Posted by Dznts

no sir. its my barely driven car..lol

Thats good. Because this will take a couple days to do.

Originally Posted by Dznts

yah gotta pin the crank, which i hear is the worst part.

It can be a big PITA. But make sure you pin it away from the notch... If i can find the pic ill show you what i mean. You also need a decent drill. I used a craftsmen batt drill... it took some goading but it got the job done.

[SinisterEcho]

Originally Posted by jewel25

Access is kicking my butt this morning. But I won

Awesome! whats that?

[Dznts]

Originally Posted by SinisterEcho

Thats good. Because this will take a couple days to do.

It can be a big PITA. But make sure you pin it away from the notch... If i can find the pic ill show you what i mean. You also need a decent drill. I used a craftsmen batt drill... it took some goading but it got the job done.

yah if you can find the pic let me know. and i have a new hilti drill, just think it might be to big to use. will have to check. i still need to go buy a torque wrench, luckily the snap on guy lives right behind me

[SinisterEcho]

Originally Posted by Dznts

yah if you can find the pic let me know. and i have a new hilti drill, just think it might be to big to use. will have to check. i still need to go buy a torque wrench, luckily the snap on guy lives right behind me

I cant find the pic anywhere. I know I have it somewhere though. I might have to dig around on my external HD for it. That or its on my dead laptop. But if you look at the crank with the pulley off you will see a notch in it. try not to do what i did and drill right next to it lol. You may have to pull the radiator off the car to do the drilling. I had just barely enough room to get the drill in. but i also moved it up and out of the way. If you were closer id let you borrow my torque set that i have.

[SinisterEcho]

Oh i posted the CAM specs in my build thread.

[jewel25]

Attachment 482806