I guess I just need to vent a little - Page 2

jimmy5 · 09-17-2012, 03:13 AM

Quote:

Originally Posted by LIM3

That sucks op. hopefully it gets better

On a side note, I would love to see your work. Do you have a site I can see it at ?

http://www.camaro5.com/forums/showthread.php?t=238810

hrpiii · 09-17-2012, 08:26 AM

I'm with Sir Nuke, this is NOT the only machine in the world with this software. I would seek out someone else or vendor for assistance. There are many many people in this world that will help, but if they don't know you need it, they cannot be there for you.

Maybe there is a similar forum for this type of work.

f5journal · 09-17-2012, 12:42 PM

What kind of machine is this. Most tinkerers use the small Shopbot, for this type of work. They are easy to set up and utilize several types of software

nm1458 · 10-04-2012, 12:48 PM

I'm not sure what software you are using, however there must be a layer created which will represent the table of your router. Physically measure your table and draw it in your program. Bottom left should be x0 y0. Make sure that watever your working on is inside your drawn table. I know this is confusing to read, you can send me a message if you like with some more info and if i can't get you started I can set you up with people that can. I program, run and maintain cnc's for a living.

C5RocksC5 · 10-04-2012, 01:42 PM

Quote:

Originally Posted by jimmy5

I am not dumping anything on anyone. The person buying it is well versed in CNC machines and the software. When I sell something I don't lie.

maybe you offer the guy some $ to help you set it up.

its a syn · 10-04-2012, 01:50 PM

Maybe their is a forum out there like ours, might find someone close to you that can help ya. Good luck!!

2001ragtop · 10-05-2012, 12:05 PM

did you buy a laser table or a water jet

10-04-2012, 01:50 PM	#20
its a syn B.O.D. 02/16/10 Drives: 2010 SGM Sp. Edition 2017 RS Conver Join Date: Jun 2010 Location: Albia,Iowa Posts: 3,959 View My Garage	Maybe their is a forum out there like ours, might find someone close to you that can help ya. Good luck!! __________________

09-17-2012, 08:26 AM	#16
hrpiii AKA "Beefcake" Drives: 2023 ZL1 Sharkskin Join Date: Oct 2009 Location: Indy Posts: 8,570	I'm with Sir Nuke, this is NOT the only machine in the world with this software. I would seek out someone else or vendor for assistance. There are many many people in this world that will help, but if they don't know you need it, they cannot be there for you. Maybe there is a similar forum for this type of work.

09-17-2012, 12:42 PM	#17
f5journal Senior Camaro Fanatic Drives: 2011 SS/RS manual - White Join Date: Aug 2010 Location: aiken, sc Posts: 1,980	What kind of machine is this. Most tinkerers use the small Shopbot, for this type of work. They are easy to set up and utilize several types of software

10-04-2012, 12:48 PM	#18
nm1458 Drives: 2010 ss/rs Join Date: Feb 2012 Location: ontario,canada. Posts: 56	I'm not sure what software you are using, however there must be a layer created which will represent the table of your router. Physically measure your table and draw it in your program. Bottom left should be x0 y0. Make sure that watever your working on is inside your drawn table. I know this is confusing to read, you can send me a message if you like with some more info and if i can't get you started I can set you up with people that can. I program, run and maintain cnc's for a living.

10-05-2012, 12:05 PM	#21
2001ragtop Drives: V8 american car Join Date: Aug 2006 Location: Dallas, Tx Posts: 1,417	did you buy a laser table or a water jet