You are browsing camaro5 
 |
|
04-14-2018, 11:02 PM
|
#1 |
 
Drives: Camaro 2ss/rs Join Date: May 2016
Location: Inland empire
Posts: 78
|
stock ss axles with 3.91 gears??
Anyone with a ss l99 auto, run the 3.91 gear setup with stock ss axles???? I understand the 1le with the 3.91 gears has the upgraded axles, but in a auto would it be worse or better on the 3.91 gears and could I get by without if I don't go more hp at the moment?? I don't race but do get on it from time to time!!! any input would be great thanks!!!!!
|
|
|
|
04-14-2018, 11:08 PM
|
#2 |
        
Drives: 2010 camaro ss Join Date: Jun 2010
Location: Port Arthur, Tx
Posts: 2,383
|
Question is how much power going through?
|
|
|
|
|
04-14-2018, 11:47 PM
|
#3 |
Drives: 2010 SS 2SS M6 Join Date: Aug 2016
Location: Smithsburg, Md.
Posts: 2,445
|
stock axles would be fine...peace
__________________
2010 SS 2SS M6 - Tune by RDP dynoSteve!(Woot) - Daily Driver - 150K! - All work by me...
|
|
|
|
|
04-15-2018, 04:27 AM
|
#4 |
Drives: 2010 Camaro 2ss/Rs Transformers Join Date: Aug 2014
Location: Yorba Linda, California
Posts: 1,564
|
stock ss axles with 3.91 gears??
I’m running stock axles still with the 3.91 gears, Multi 3600-3700 stall with fbo, e85, Carbon fiber one piece driveshaft, poly engine mounts, poly diff bushing, and more suspension upgrades and the axles are holding up very nicely. Just have trouble getting the power down to get traction haha. You should be fine unless you are making a lot more hp and torque to the wheels. I might upgrade the axles later down the line just because haha. So, to answer your question yes you are fine running the 3.91 gears on your l99 with stock axles.
__________________
YouTube:Krisprz garage
Insta:kris__perez & krisprz_garage LS3 conversion Vararam intake(tune model) Kooks LT headers & cats delete Corsa ZL1 3" exhaust RedBarn Racing Tune CMS Stage 3 Cam AFR CNC ported heads MSD Spark plug wires LNC-2000 Launch controller NGK TR6 Spark Plugs 1le strut tower brace-TPIS spacers Nick Williams 102mm throttle body Fast lsxr 102 intake manifold Slp 25% UDP Katech Tensioner Pulley Circle D 3600-3700 multi disk Stall GM 3.91 gears DDS carbon fiber driveshaft ZL1 fuel pump & injectors Flex fuel sensor(91/E85) https://wheelwell.com/kris-perez |
|
|
|
|
04-15-2018, 09:26 AM
|
#5 |
|
Drives: Camaro 2ss/rs Join Date: May 2016
Location: Inland empire
Posts: 78
|
This is sounding good�� Im respectfully running about 50 more hp than stock and all the suspension has been replaced with bmr and running 305 tires in the rear. Stock stall converter and upgraded to fe4 sway setup in the rear, so should be slightly more hp than the 1le but that car comes with heavier axles right??? Chevy just being careful??is the load transfer on a manual drive setup much harder than an auto setup?
|
|
|
|
|
|
|
|
 |
|
|
