03-11-2015, 05:57 PM | #29 |
700RWHP-650TQ
Drives: 2011 Forged LS3 Supercharged/Cammed Join Date: Aug 2010
Location: Shrewsbury Massachusetts
Posts: 5,269
|
If you guys are on the fence. Here is some Rideskinz Porn for you.
The amount of comments i get on my bumper is insane. Every camaro owner i run into, first thing out of their mouth...."Wow..What bumper is that" With that said this is the Fiberglass Version 1. But is 90% the same as the new version 2. As far as ride height. My Cars suspension is all STOCK. This bumper sits approximately 1" lowering the front than the stock. Not a huge difference at all, no different than adding an aftermarket lip. I don't have any issues under normal driving areas. Highly recommended!
__________________
View Build HERE>>>>>MY 2011 2SS/RS JOURNAL |
03-11-2015, 06:21 PM | #30 |
Drives: 2013 White L99 SS Join Date: Dec 2013
Location: Great Falls, VA
Posts: 225
|
I'm surprised there aren't more people interested in this group buy!
Sent from my iPhone using Tapatalk
__________________
Current HP/Torque: 413HP/413 Torque
Current mods: Pfadt Tri-y Headers with Hi-Flow Cats, VMAX CNC Ported Throttle body, CAI intake by Cold Air Inductions, Apex Air Scoop/Washer relocation set, RX Catch Can, Stainless Works 3" retro Chambered cat back exhaust, Flex Fuel sensor, 3.91 gear ratio, BMR rear trailing arms, BMR Rear Toe rods Future Mods: GPI's SS3 VVT cam, 3600 stall triple disc torque converter, Fast LSX 102mm throttle body |
03-11-2015, 09:13 PM | #31 |
Drives: 2013 Camaro RS 1LT, 6M Join Date: Jan 2013
Location: Albany, OR
Posts: 603
|
I might be in a couple months but not sure. Couple of thing needs to line up first. Bad ass and crossing my fingers. Hopefully the group buy will be still on.
__________________
|
03-12-2015, 11:06 AM | #32 | |
Drives: SS, ZL1, V6 Join Date: Jan 2012
Location: So Cal
Posts: 836
|
Quote:
|
|
03-12-2015, 11:58 AM | #33 |
Drives: 2010 Camaro 2SS/RS Join Date: Aug 2012
Location: Cordova, TN
Posts: 774
|
I may be interested if the DRL's came with the bumper... and ONLY if the bumper had the mailslot still in it. Can this be done?
__________________
2010 Camaro 2SS M6
2" Stainless Power Longtube Headers 3" Full exhaust w/ Off-Road H-Pipe Bo White Ported Throttle Body Hurst Short Throw Shifter Best Time: 12.43 @ 114, 1.99 60' on stock wheels and stock tires Build Thread |
03-12-2015, 12:14 PM | #34 |
Drives: '11 SW 2SS/RS LS3 Vert Join Date: Jul 2013
Location: Ontario, Canada
Posts: 156
|
|
03-16-2015, 06:13 PM | #35 |
Drives: '11 SW 2SS/RS LS3 Vert Join Date: Jul 2013
Location: Ontario, Canada
Posts: 156
|
Calling out to all those who are on the fence ... we are only a few away from GB pricing
|
03-17-2015, 04:27 PM | #36 | |
Drives: Black L99 2SS/RS Join Date: Mar 2014
Location: San Antonio, TX
Posts: 1,862
|
Quote:
edit: So these are all going to be UNPAINTED? Because if that's the case, I definitely would rather just buy my own and have it come painted already. I understand it's for warranty reasons, but wouldn't it be better to buy individually and have it done the way you wanted? |
|
03-17-2015, 06:57 PM | #37 |
Drives: SS, ZL1, V6 Join Date: Jan 2012
Location: So Cal
Posts: 836
|
Here is the info from the original Aggressor 2 group buy:
Rideskinz Custom Automotive Design is back with a new and improved POLYURETHANE front bumper fascia... The Aggressor 2 That's right, the new Aggressor 2 will be offered in flexible and durable polyurethane. No more worrying about cracking or fitment issues. This replacement bumper will give you the security of knowing that it will not crack or break over time. So you pay more for the peace of mind than anything. We have taken all the feedback, ideas and suggestions from our customers on the fiberglass Aggressor LTZ 1 bumper and transformed it into something that everyone can truly appreciate. Everything from ground clearance, upper grille and fender fitment, sidemarker light fitment, lower lip design, etc. has been addressed in the new Aggressor 2 front fascia. We at Rideskinz appreciate all of your patience, efforts and enthusiasm and hopefully you will show your support as our company continues to grow. For those of you not familiar with Rideskinz, we welcome you! Photo's of the Aggressor 2: This image has been resized. Click this bar to view the full image. The original image is sized 1500x2000. No mail slot: This image has been resized. Click this bar to view the full image. The original image is sized 1500x1023. This image has been resized. Click this bar to view the full image. The original image is sized 1500x1046. This image has been resized. Click this bar to view the full image. The original image is sized 1500x2000. This image has been resized. Click this bar to view the full image. The original image is sized 1500x1125. This image has been resized. Click this bar to view the full image. The original image is sized 1500x1164. This image has been resized. Click this bar to view the full image. The original image is sized 1500x1121. This image has been resized. Click this bar to view the full image. The original image is sized 1500x2184. This image has been resized. Click this bar to view the full image. The original image is sized 1500x2135. This image has been resized. Click this bar to view the full image. The original image is sized 1500x2000.
Options:
The Aggressor 2 polyurethane bumper comes unpainted with a black satin finish. This bumper may require minor prepping, sanding, shaving, filling, cutting, or other body work. All parts provided are for show use only and may not be legal for use on public roads. Removal of any safety equipment on the vehicle is the sole responsibility of the recipient, and the manufacturer shall not be held liable. We are not responsible for labor expenses, towing expenses, additional repair expenses or rental car expenses caused by the use of wrong or defective parts during installation. |
03-17-2015, 07:02 PM | #38 | |
Drives: SS, ZL1, V6 Join Date: Jan 2012
Location: So Cal
Posts: 836
|
Quote:
|
|
03-17-2015, 07:15 PM | #39 | |
Drives: Black L99 2SS/RS Join Date: Mar 2014
Location: San Antonio, TX
Posts: 1,862
|
Quote:
I have a relative that lives in San Juan Capistrano, Orange County. |
|
03-17-2015, 07:31 PM | #40 |
Drives: SS, ZL1, V6 Join Date: Jan 2012
Location: So Cal
Posts: 836
|
|
03-17-2015, 07:53 PM | #41 |
Drives: 2013 White L99 SS Join Date: Dec 2013
Location: Great Falls, VA
Posts: 225
|
Yea now I would need to find a place to paint it, considering I'm on the other side of the country lol
Sent from my iPhone using Tapatalk
__________________
Current HP/Torque: 413HP/413 Torque
Current mods: Pfadt Tri-y Headers with Hi-Flow Cats, VMAX CNC Ported Throttle body, CAI intake by Cold Air Inductions, Apex Air Scoop/Washer relocation set, RX Catch Can, Stainless Works 3" retro Chambered cat back exhaust, Flex Fuel sensor, 3.91 gear ratio, BMR rear trailing arms, BMR Rear Toe rods Future Mods: GPI's SS3 VVT cam, 3600 stall triple disc torque converter, Fast LSX 102mm throttle body |
03-17-2015, 07:58 PM | #42 | |
Drives: Black L99 2SS/RS Join Date: Mar 2014
Location: San Antonio, TX
Posts: 1,862
|
Quote:
So would you recommend the group buy and have a local place paint this sucker factory black? Or individual buy and have him go pick it up locally and ship it himself to me? |
|
|
|
|
|