2010 Inner door weatherstrip seal? - Page 3 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

SummitWhite11 · 10-01-2017, 11:17 AM

Quote:

Originally Posted by km9v

You can get that part on Amazon for $250.

https://www.amazon.com/Genuine-GM-We.../dp/B00TABJFYW

Thanks for the lead - still too much money for my taste on a piece of rubber.

gringo · 10-02-2017, 08:10 AM

Quote:

Originally Posted by myold88

How do you know? Did you go to the flat rate manuel? Replace
yours already? Explain. Insults and talk is so cheap on line.

I wouldn't even need to consult the manual for something simple like this.

It is one complete piece. Start lifting one part up and then start pulling and the whole thing will come off. I've done it countless of times with similar vehicles at the junkyard. No service manual required.

MSgt O · 09-14-2022, 03:41 PM

bringing it back from the dead...anyone replace this? do you just pull it out and slip the new one on?

CPCNY · 09-14-2022, 05:49 PM

Quote:

Originally Posted by MSgt O

bringing it back from the dead...anyone replace this? do you just pull it out and slip the new one on?

The strip has plastic nubs that insert into holes in the rocker panel. I put zl1 rockers on my car and it came with new weather stripping. Took 30 seconds to put it on but pay attention to orientation. There is a front and back on the strip.

MSgt O · 09-14-2022, 07:21 PM

the weather stripping for the door seal goes into the rockers??? cant see how that possible?!?!

NOT A 45 · 09-15-2022, 06:49 AM

Quote:

Originally Posted by MSgt O

the weather stripping for the door seal goes into the rockers??? cant see how that possible?!?!

No it doesn't go into the rockers.....it slips over the pinch weld around the entire door opening. A word of caution when you install it....do not stretch it or you will end up with several inches too much weather strip when you reach the end. Actually I see yours is a convertible but even so don't stretch it.

joekono · 09-15-2022, 08:14 AM

Try this place(dealership):https://www.maloufpartsxperts.com/oe...strip-22950429. I know it's 276.00 and the convertible one that was posted earlier in the thread was $180.00. They are genuine GM parts and I had the same exact issue you have. It was such an eyesore. I can't speak for the Amazon versions but the weather strip I bought had a bead of glue on the inside and was easy to install. Hope this helps.

myold88 · 09-15-2022, 08:53 AM

Quote:

Originally Posted by speedup

My weather stripping is wearing in the exact same spots as OP. Car is still under warranty. I was at the dealer for another warranty issue, and asked them if they would replace it.. they said no, lol.

Nothing funny about it. Warrantees to not cover wear and tear damage.
If you had a dent in your fender would you expect GM to fix it? Same thing

MSgt O · 09-15-2022, 10:35 AM

Thanks 45 and Joe! if it just peels off the pinch weld, too easy...I have the part in hand, ordered it and it just looked odd when i got it. think the back end i have to remove the side panel top cover and it fits into something under it...its triangled shaped..lets give it a whirl and see what happens...

Aqua Blue RS/SS · 09-15-2022, 12:24 PM

Quote:

Originally Posted by myold88

Nothing funny about it. Warrantees to not cover wear and tear damage.
If you had a dent in your fender would you expect GM to fix it? Same thing

That post was from 5 years ago…

NOT A 45 · 09-15-2022, 12:47 PM

Quote:

Originally Posted by MSgt O

Thanks 45 and Joe! if it just peels off the pinch weld, too easy...I have the part in hand, ordered it and it just looked odd when i got it. think the back end i have to remove the side panel top cover and it fits into something under it...its triangled shaped..lets give it a whirl and see what happens...

You may have to pull a trim piece or 2 off, but no doubt I'm sure you can handle this job. Like I said though, don't stretch it.....just lay it in place and push it onto the pinch weld.....I'd probably start from the back.

Nenous1 · 08-19-2023, 08:34 AM

Trying find some weather stripping myself, talk about expensive.

SummitWhite11 · 08-19-2023, 03:14 PM

Quote:

Originally Posted by Nenous1

Trying find some weather stripping myself, talk about expensive.

I'm the OP of this post and no I still have not replaced it yet! Ha! I agree its way too much $ on a piece of rubber. Ridiculous!

1JEWLDSSRS · 08-19-2023, 04:34 PM

Have you check a local bone yard yet to see if they have any wrecked Camaros?? Get one from there. They'll probably let you have it for free...

09-15-2022, 08:14 AM	#35
joekono Drives: Camaro Convertible 2014 1LT Join Date: May 2019 Location: New Jersey Posts: 1,013 View My Garage	Try this place(dealership):https://www.maloufpartsxperts.com/oe...strip-22950429. I know it's 276.00 and the convertible one that was posted earlier in the thread was $180.00. They are genuine GM parts and I had the same exact issue you have. It was such an eyesore. I can't speak for the Amazon versions but the weather strip I bought had a bead of glue on the inside and was easy to install. Hope this helps. __________________

08-19-2023, 04:34 PM	#42
1JEWLDSSRS Drives: 2011 SS-RS Join Date: May 2011 Location: FLORIDA Posts: 11,472	Have you check a local bone yard yet to see if they have any wrecked Camaros?? Get one from there. They'll probably let you have it for free... __________________ TSP STAGE 3 CAM,231/246 @112 LSA 614/641 LIFT, CIRCLE D 5C-4200-4500 CONVERTER,LOD INTAKE.CORSA EXHAUST. DSS 1 PC DS. PEGASUS SOLID CRADLE MOUNTS. 486RWHP/475RWTQ.LOTS MORE.

09-14-2022, 03:41 PM	#31
MSgt O Drives: 2012 Camaro 2SS/RS Vert LS3/M6 Join Date: Aug 2021 Location: Cheboygan, Michigan Posts: 660	bringing it back from the dead...anyone replace this? do you just pull it out and slip the new one on?

09-14-2022, 07:21 PM	#33
MSgt O Drives: 2012 Camaro 2SS/RS Vert LS3/M6 Join Date: Aug 2021 Location: Cheboygan, Michigan Posts: 660	the weather stripping for the door seal goes into the rockers??? cant see how that possible?!?!

09-15-2022, 10:35 AM	#37
MSgt O Drives: 2012 Camaro 2SS/RS Vert LS3/M6 Join Date: Aug 2021 Location: Cheboygan, Michigan Posts: 660	Thanks 45 and Joe! if it just peels off the pinch weld, too easy...I have the part in hand, ordered it and it just looked odd when i got it. think the back end i have to remove the side panel top cover and it fits into something under it...its triangled shaped..lets give it a whirl and see what happens...

08-19-2023, 08:34 AM	#40
Nenous1 Drives: 2011 Camaro rs Join Date: Jun 2023 Location: NC Posts: 65	Trying find some weather stripping myself, talk about expensive.