You are browsing camaro6 
09-19-2019, 01:49 PM
|
#1 |
 Drives: 64vette,2010 2SS,2013 Zl1 Join Date: Mar 2013
Location: kanata,on,can.
Posts: 89
|
front camera
I installed a camera in front of my 2019 ZL1 but I can't figure how to get the wires for the display from the engine compartment to the front seat, anybody done that already.
|
|
|
|
09-19-2019, 02:07 PM
|
#2 |
 Drives: 2018 Camaro ZL1 Join Date: Feb 2011
Location: Midwest
Posts: 255
|
grommet
There is a small grommet on the part of the door jam where the hinges bolt. I used a small exacto-knife to create a small hole and fed the wires through inside the cabin. Then sealed it up with some 3m strip caulk. No water leaks yet!!
|
|
|
|
|
09-19-2019, 02:22 PM
|
#3 |
         
Drives: 18 ZL1 A10 Join Date: Nov 2008
Location: South East, FL
Posts: 3,024
|
behind the master cylinder there is a big harness and grommet. slice grommet.
__________________
2017 ZL1 M6 Bog City, 2013 ZL1 M6, 2010 2SS M6
ZL1::J-E-T-S JETS JETS JETS  |
|
|
|
|
09-19-2019, 02:50 PM
|
#4 |
|
Who Needs to KNOW?
Drives: 18 ZLE Join Date: May 2018
Location: Left Side of the Moon
Posts: 1,770
|
If not too many wires or thin, use hood release grommet hole - try to avoid cutting grommets - that's how you get water / moisture in the car in places not designed for it.
__________________
 ing for grip.Are you in the NY/NJ/PA/CT region? Join us for autox fun at MetLife Stadium. HUGE lots, tons of runs. http://www.motorsportsne.com/ |
|
|
|
|
09-19-2019, 07:54 PM
|
#5 |
|
TBC
Drives: 2017 Fifty 2ss Join Date: Dec 2012
Location: St Petersburg Fl
Posts: 196
|
Can u add one to a 18?
__________________
2017 Fifty A8, MRC, NPP, NAV, LUM, BLK BOWTIE
|
|
|
|
|
09-19-2019, 08:06 PM
|
#6 |
|
Who Needs to KNOW?
Drives: 18 ZLE Join Date: May 2018
Location: Left Side of the Moon
Posts: 1,770
|
5th gen DIY has a kit based on hardware from corvette IIRC.
__________________
ing for grip.Are you in the NY/NJ/PA/CT region? Join us for autox fun at MetLife Stadium. HUGE lots, tons of runs. http://www.motorsportsne.com/ |
|
|
|
|
09-19-2019, 08:36 PM
|
#7 |
|
2018 Garnet Red ZL1 conve
Drives: 2013 & 2018 ZL1 vert Join Date: May 2009
Location: Des Moines, IA
Posts: 1,471
|
I have the Gen5DIY.com front camera kit. Their web page has install videos. Love it!
__________________
 Build Thread: 2018 ZL1 Vert Purchased (Overpar73) |
|
|
|
|
09-21-2019, 10:10 AM
|
#8 |
|
Drives: 64vette,2010 2SS,2013 Zl1 Join Date: Mar 2013
Location: kanata,on,can.
Posts: 89
|
front camera
I had a 2013 zl1 and installed a front camera which displayed in the that cost me about $15.all the pictures and how to do the work are somewhere in 2013 or 14 but I had the shop manuals. GM has not release the 2019 yet and don't know if the plan to so until I can get wiring info, I have a 4" display infront of the transmission stick and that works very good and cost $25. Anybody who has the wiring info, that would be verymuck appreciated
|
|
|
|
|
|
|
|
|
Post Reply
|
| Thread Tools | |
|
|
