01-07-2014, 01:28 PM | #15 | |
7 year Cancer Survivor!
Drives: 17 Cruze RS, 07 G6 GT, 99 Astro Join Date: Dec 2007
Location: East Tennessee
Posts: 21,547
|
Quote:
You may want to consider hex vents I am sure you could get them to work.
__________________
Cancer's a bitch! Enjoy life while you can! LIVE, LOVE, DRIVE...
The Bird is the word! |
|
01-07-2014, 01:40 PM | #16 |
Drives: '21 ZLE A10 Join Date: May 2012
Location: Mechanicsville, VA
Posts: 6,808
|
If no one responds to this request, I will measure mine tonight for you.
__________________
'21 ZLE A10 Wild Cherry PDR 2:00.78 VIR Full 10.68@131.69 1.68 60'
'17 ZL1 A10 Mosaic Black PDR/Nav 2:03.08 VIR Full 11.003@129.2 1.75 (sold) '15 Z/28 #325 Black a/c & stereo. 2:10.1 VIR Full (sold) '12 ZL1 A6 Black 10.52@131 1.55 60' 2:13 VIR Full (sold) |
01-07-2014, 01:40 PM | #17 | |
Drives: 1987 Corvette TPI Join Date: Mar 2012
Location: Littleton
Posts: 549
|
Quote:
|
|
01-07-2014, 01:42 PM | #18 |
Drives: 1987 Corvette TPI Join Date: Mar 2012
Location: Littleton
Posts: 549
|
Thank you!
|
01-07-2014, 01:48 PM | #19 |
7 year Cancer Survivor!
Drives: 17 Cruze RS, 07 G6 GT, 99 Astro Join Date: Dec 2007
Location: East Tennessee
Posts: 21,547
|
I would go out and measure mine but it's under a blanket if snow and it's 10F outside.
__________________
Cancer's a bitch! Enjoy life while you can! LIVE, LOVE, DRIVE...
The Bird is the word! |
01-07-2014, 01:53 PM | #20 |
Older Than Dirt
Drives: 2010 & 2013 Camaros Join Date: Apr 2010
Location: Aiken, SC
Posts: 4,564
|
Just in front of the scoop openings, it's about 21-7/16" wide. About 6" from the rear of the insert, it's about 23-3/4" wide. About 40-1/2" long from front point to the back.
All measurements done by my wife's super-accurate (yeah, right) cloth sewing measuring tape and thus listed as approximate. But this should give you an idea.
__________________
2010 2SS TE, 1 of 822/2013 Camaro ZL1 vert, 1 of 54
|
01-07-2014, 01:54 PM | #21 |
Drives: 1987 Corvette TPI Join Date: Mar 2012
Location: Littleton
Posts: 549
|
I understand, thank you.
|
01-07-2014, 01:55 PM | #22 | |
Drives: 1987 Corvette TPI Join Date: Mar 2012
Location: Littleton
Posts: 549
|
Quote:
|
|
01-07-2014, 01:58 PM | #23 |
Drives: 2017 Mosaic Bk ZL1 M6 Join Date: Jul 2009
Location: South of Raleigh, NC
Posts: 9,477
|
Are you sure it will apply downforce? GM spent a lot of money and man hours in the wind tunnel to get this system to work on the ZL1. No doubt it will look cool, though. Good luck with the project.
__________________
|
01-07-2014, 01:58 PM | #24 |
Drives: 1987 Corvette TPI Join Date: Mar 2012
Location: Littleton
Posts: 549
|
I just measured the cowl on my C4 and it should fit just about perfect! A little modding is understandable as this is not going on a Camaro. I'll also welcome other measurements
|
01-07-2014, 02:05 PM | #25 |
Drives: 1987 Corvette TPI Join Date: Mar 2012
Location: Littleton
Posts: 549
|
Yes it should, the air goes just under the nose through the radiator then out the ZL1 extractor hopefully
|
01-07-2014, 05:31 PM | #26 |
Drives: 2013 Camaro ZL1 Join Date: Dec 2012
Location: Dallas, Texas
Posts: 2,155
|
Unless you make provisions for the catch basin over your radiator as the ZL1 has you will get water runoff into the engine compartment.
|
01-07-2014, 07:27 PM | #27 |
Drives: '21 ZLE A10 Join Date: May 2012
Location: Mechanicsville, VA
Posts: 6,808
|
look at a pic of the insert. It is 41" from the cowl to the front point center to center. It is 22 1/2" wide at the center point of the hood.
__________________
'21 ZLE A10 Wild Cherry PDR 2:00.78 VIR Full 10.68@131.69 1.68 60'
'17 ZL1 A10 Mosaic Black PDR/Nav 2:03.08 VIR Full 11.003@129.2 1.75 (sold) '15 Z/28 #325 Black a/c & stereo. 2:10.1 VIR Full (sold) '12 ZL1 A6 Black 10.52@131 1.55 60' 2:13 VIR Full (sold) |
01-07-2014, 08:13 PM | #28 |
Drives: 1987 Corvette TPI Join Date: Mar 2012
Location: Littleton
Posts: 549
|
It will clear the engine plenty, my worry is it actually going to far forward and touching the radiator.
|
|
|
|
|