05-04-2014, 07:55 PM | #1 |
618 RWHP
|
looking for help on bowtie
I just bought a ZL1 . I want to replace or change the factory bowtie . I would like to have the yellow part of the bowtie to be black and keep the border chrome. Any one know the easiest way to do this ?. Dose any know where i can buy one like that ? or how to change the ones i have. I don't mind spending the money. I just wont it to look like it came from the factory that way .
|
05-04-2014, 08:13 PM | #2 |
bigwormgraphix has what you're looking for
__________________
|
|
05-04-2014, 11:51 PM | #3 |
Madman
|
goo to local vinyl guy..cheaper easier..someone who letter scars & trucks...they may even give ya free black scrap pieces..and/or help ya
|
05-05-2014, 12:15 AM | #4 |
Drives: 2014 2SS L99 Join Date: Mar 2014
Location: Corpus Christi Texas
Posts: 1,320
|
I just cleaned the entire bowtie with naptha based lighter fuel and wiped dry. Carefully masked off the chrome bezel and applied three coats of black metallic Dupli-Color enamel. Came out nice. Did the same to my 2012 Chevy Silverado a couple of years ago. It has held out well and looks better than vinyl overlays up close. Here's a shot of the Camaro bowtie:
And here's the one I did on my truck: |
05-05-2014, 04:47 AM | #5 |
Drives: 2012 Camaro 45th Anniversary RS Join Date: Nov 2012
Location: New York
Posts: 2,418
|
I say vinyl or plastidip. The most cost effective and non permanent. I just did my wife's truck with gloss black vinyl. Got it on eBay for around 7 bucks shipped for a 1'x 5' roll.
|
05-05-2014, 09:41 AM | #6 |
Drives: 2011 ss Join Date: Aug 2012
Location: Smyrna tn.
Posts: 166
|
Hobby Lobby sells small 12"/12" squares of all colors of vinyl ..just cut a piece a little larger than needed,,then pull off the backing stick it over bow tie then trim around the inside chrome edge with razor knife..
Cost @ $.97 plus tax. Last edited by Jcm; 05-05-2014 at 11:38 AM. |
05-05-2014, 09:46 AM | #7 |
Teenage Dream Camaro
Drives: A Visually Stunning Camaro Join Date: Feb 2013
Location: Florida
Posts: 1,722
|
tower decals has them for pretty cheap
__________________
White shoes at the black show
|
05-05-2014, 10:48 AM | #8 |
Drives: 2014 1LT Join Date: Jan 2014
Location: USA
Posts: 226
|
I did the vinyl but did not like how it turned out so I went with this - http://www.chevymall.com/2014-Camaro...462/4313|4314/
|
05-05-2014, 12:56 PM | #9 |
Drives: 2014 2LS Join Date: Dec 2013
Location: ATL
Posts: 134
|
How can I make my bowtie like the Z/28 bowtie
|
05-05-2014, 01:20 PM | #10 |
Drives: 2016 Camaro 2SS M6 Black Join Date: Nov 2013
Location: Bremerton, WA
Posts: 582
|
A dremel tool.
As for the OP, I bought some GM black touch up paint from advanced auto. It has a brush that is like a nail polish brush that I used to paint mine. Super easy and if you get it on the chrome by accident it comes right off. |
05-05-2014, 04:43 PM | #11 |
Drives: 2013 SS LS3 Join Date: Nov 2011
Location: Littleton, CO
Posts: 475
|
carbon fibor overlay, $10 for a sheet the size of a sheet of paper. Just like vinyl, very easy to use.
|
|
|
|
|