01-04-2015, 03:28 PM | #1 |
Drives: 2013 Camaro 2LT convert Join Date: Feb 2014
Location: Auburn,NY
Posts: 27
|
GM #22950575 1le splitter
I bought side skirts and splitter of a member who would not split up the pair. The splitter come off a 2013 V8 Hot Wheels car after one summer of use, that will not fit my car. I bought a new installation kit for almost $150. that has every thing you need to install. The splitter is in very nice condition, no curb rash. $350. plus shipping.
|
01-05-2015, 02:32 PM | #2 |
[COTW 1/6/14]
Drives: 2017 1LE Join Date: Mar 2012
Location: Scott AFB/STL
Posts: 2,004
|
just wondering do you think the hardware would work on a 2014 1LE splitter?
|
01-05-2015, 10:26 PM | #3 |
"Cam Only"
|
Would you do $300 shipped to California? (Genuine question, not trying to lowball)
__________________
2013 AGM Camaro 2SS/RS M6 | LSA Blower, 2.5" pulley, 10% lower, FIC1000's, Fore Innovations Twin Pump fuel system w/ Flex Fuel, CMS Custom Grind Cam, Kooks 1 7/8" headers w/ catless off-road pipes, NPP Exhaust, 3.91's, JLT ZL1 Intake, Prospeed Heat Exchanger | Pfadt Suspension, 1LE Sway Bars | DSS 1000hp axles |
Tuned by Ryne @ CMS E85: 734rwhp/636rwtq (mustang dyno) |
01-06-2015, 01:55 PM | #4 |
Drives: 2013 Camaro 2LT convert Join Date: Feb 2014
Location: Auburn,NY
Posts: 27
|
Jeff. Thanks for the offer but I can't do that.
|
01-06-2015, 07:33 PM | #5 |
"Cam Only"
|
How much do you think shipping would be to say 91301 (southern California)? Rough estimate?
I could do more depending on how much shipping is..
__________________
2013 AGM Camaro 2SS/RS M6 | LSA Blower, 2.5" pulley, 10% lower, FIC1000's, Fore Innovations Twin Pump fuel system w/ Flex Fuel, CMS Custom Grind Cam, Kooks 1 7/8" headers w/ catless off-road pipes, NPP Exhaust, 3.91's, JLT ZL1 Intake, Prospeed Heat Exchanger | Pfadt Suspension, 1LE Sway Bars | DSS 1000hp axles |
Tuned by Ryne @ CMS E85: 734rwhp/636rwtq (mustang dyno) Last edited by Jeff_SS; 01-06-2015 at 08:40 PM. |
01-06-2015, 08:34 PM | #6 | |
|
Quote:
Ed M.
__________________
RJT 2SS/RS, AAM 3.70's, MTI Sway Bars, Shifter & SS brake lines, ZLI calipers, rotors & pads, BMR Trailing & Toe Arms, rear cradle & diff bushes, Pedders XA's, Camber/Toe eccentrics, Radius arm inserts, GTO clutch reservoir, LS9 cam, Comp valve springs, Melling 10296 oil pump, CR5 timing chain, LS6 damper, CAI Cold Air Intake, ARH LT headers w/HF cats, GMPP touring axle back, Elite Engineering Catch Can, Forgeline 20x9.5 & 20x11 DS3 whls, 275/40/20 & 315/35/20 tires, 2011 Convertible spoiler, 1LE front spoiler, Lloyd "SS" Floor Mats, GM Camaro Trunk Mat, wrapped console & Grant steering wheel.
|
|
01-07-2015, 01:42 PM | #7 |
Drives: 2013 Camaro 2LT convert Join Date: Feb 2014
Location: Auburn,NY
Posts: 27
|
Jeff_SS and flht99b PM,d
__________________
|
01-07-2015, 01:49 PM | #8 |
Let's go Rangers!
|
The OP probably does not know this but I thought I'd point it out to 1- advise the buyer and 2- make the OP aware of it so he does not have an issue later on from the buyer wanting a refund.
I can see from the OP's pic the that the splitter does not have the 2 end caps (not sure what to call them), they are missing. You can see them in the pic below (pic from one I sold), look to the right and you'll see a small hole. You need these to hold the side on and these DO NOT come in the install pack as they are actually part of the splitter, in fact I'm not even sure they are sold separately but not 100% sure on that. These are a know issue (and bad design) on these splitters as they frequently loosen up and then need to be glued on or the splitter replaced. Again OP I am not trying to hurt you sale, just want you and the buyer to be aware as this will not be cheap to ship and you'll someone will stand to lose some money. So seller and buyer beware. Actually here is a better pic, see the 2 holes on each end, this is how the sides are screwed down: See bottom left of pic, this should clarify what I mean. Last edited by nyrfan; 01-07-2015 at 02:11 PM. |
08-05-2015, 03:58 PM | #9 |
Drives: 2014 Camaro 2SS 1LE Join Date: Jul 2014
Location: St. Louis, MO
Posts: 28
|
Why is one black and the other primered white?
|
08-05-2015, 09:50 PM | #10 |
Drives: 2011 CAMARO SIM 2SS/RS Join Date: Nov 2012
Location: Chicago
Posts: 598
|
Price shipped to 60608?
|
08-06-2015, 12:15 AM | #11 |
Drives: 2011 Camaro 2Ss M6 Join Date: Dec 2011
Location: Southern California
Posts: 4,013
|
NYRFAN made a good point. Those two pieces are very much necessary to complete the install. Ill be holding off until a complete one shows up..
|
|
|
|
|