04-05-2017, 04:03 PM | #57 |
Drives: 2017 Camaro 1LE Join Date: Jan 2017
Location: Jacksonville, FL
Posts: 51
|
I was going to edit that post but I don't mind looking like an idiot. My voltages were way off. Here is a video I just took. I wired it up in parallel with my wife's cooled seats and viola it works and with voltages.
https://youtu.be/kri0lECyPHo Like you said, we just need a way to controlled it. Maybe a resistor, I don't need speeds, wide open is fine with me, lol |
04-05-2017, 04:06 PM | #58 | |
Drives: 2017 SS 1LE Join Date: Mar 2016
Location: Monterey, CA
Posts: 2,474
|
Quote:
__________________
IG: @NC_M1SS1LE
|
|
04-05-2017, 04:07 PM | #59 |
Drives: 2017 Camaro 1LE Join Date: Jan 2017
Location: Jacksonville, FL
Posts: 51
|
Recap correct voltages on blue wire:
High 1.23v Med 2.88v Low 4.55v Off 12.7v Red wire has 12.7 all the time, and black is ground (obviously) I'm not super electronic savvy so if it's PWM or not, I'm not sure. I hope not because you could just run a resistor across the red and blue and make it one speed all the time. Last edited by Camaro6717; 04-06-2017 at 01:02 PM. |
04-05-2017, 06:44 PM | #60 |
Drives: 2017 1ss1le Join Date: Feb 2017
Location: Jacksonville, Fl
Posts: 142
|
Switches are easy. Multiple options.
If someone runs across a wire diagram we can get it figured out. I'm sure there is a tap somewhere on the CAN we can use. I thought about using the climate control with the seat buttons already. It is on CAN, but requires other sensors to make function. I haven't had much luck with the 2017 system finding info. The memory seats have a separate module connected to the switch. Last edited by Summit1le1ss; 04-05-2017 at 06:54 PM. |
04-05-2017, 07:00 PM | #61 |
Drives: SW 1SS 1LE / Jeep XJ Join Date: Mar 2016
Location: WPB,FL
Posts: 799
|
So yes the fan spins but do we have that vented foam? Should be able to feel it through the seat.
|
04-05-2017, 07:20 PM | #62 |
Drives: 2016 SS Nightfall Gray Join Date: Oct 2016
Location: Las Vegas
Posts: 196
|
|
04-05-2017, 09:41 PM | #63 |
Drives: 2017 Camaro 1LE Join Date: Jan 2017
Location: Jacksonville, FL
Posts: 51
|
I bought some resistors and crap, I have minimal knowledge of this kinda stuff but I found a diagram on how to get 12v down to 1.25v so I'm gonna try that and see if it blows thru the seat.
If we could find buttons like above that have the built in resistors it would make this a breeze. I plan on using 12v from the cigarette plug. |
04-05-2017, 10:27 PM | #64 |
Drives: 17 SS 1LE Join Date: Dec 2015
Location: Houston
Posts: 1,920
|
The 2LT has heat/vent seats without memory as standard. So comparing the harness could tell us a lot about which pins do what.
http://www.thatgmpartsguy.com/auto-p...umber=23379512 |
04-05-2017, 11:30 PM | #65 |
Drives: 2017 Camaro 1LE Join Date: Jan 2017
Location: Jacksonville, FL
Posts: 51
|
So I got my contraption all wired up and got 1.25v out of it. Supplied the red with 12.5v, black to ground and the 1.25v to the blue and..................NOTHING!!!! Either I'm missing something here or this may need PWM power.
On another note, the car has all the fuses in the fuse box for heated/vented seats installed. We need an insider at GM to tell us whats going on and how to activate this. Last edited by Camaro6717; 04-05-2017 at 11:52 PM. |
04-06-2017, 02:49 AM | #66 |
Drives: 2017 1SS 1LE Black on Black Join Date: Feb 2017
Location: Arizona
Posts: 108
|
following.....you all are sooo close.....HA HA.. bring it home fellas!!!!
|
04-06-2017, 03:14 AM | #67 |
SABIO
Drives: 2016 CAMARO 1SS Join Date: Jul 2015
Location: Bradford, ON
Posts: 5,012
|
Someone if going to set their seats on fire while they are driving...............
__________________
|
04-06-2017, 04:31 AM | #68 |
Drives: 2017 1ss1le Join Date: Feb 2017
Location: Jacksonville, Fl
Posts: 142
|
If it's can there is no ground.
The switch would be supplied with 12v and the volts would be send determined by the speed setting. Each wire on the fan would be a different voltage. Sometimes it can be a closed loop system where only volts need to be send, some need info to be sent back to complete the loop and operate. Edit: what type of car did you try this on where it worked? I'll grab that diagram and see what I see. |
04-06-2017, 07:45 AM | #69 |
"M1SS1LE"
Drives: 2017 SS 1LE Join Date: Dec 2015
Location: Upstate SC
Posts: 2,906
|
I think its pretty safe to say if they didn't bother to remove the fans then they certainly didn't bother to use 2 different types of foams. These are the exact seats that come in a 2LT 1LE. I would bet a paycheck that all the stuff is there we just have to figure out how to wire them.
__________________
MJK3888 Instagram Link
|
04-06-2017, 07:51 AM | #70 |
Drives: 2017 SS 1LE Mosiac Black Join Date: Nov 2016
Location: DFW, TX
Posts: 1,132
|
These 1LEs are full of surprises, like getting the ZL1's in tank fuel pump.
|
|
|
Post Reply
|
|
|