ZL1 stone/splash guards - Page 16

DANACO · 11-12-2018, 02:29 PM

Received mine this morning

Staubsauger17 · 11-12-2018, 03:58 PM

E-mail sent to ACS! Awaiting response.

Staubsauger17 · 11-12-2018, 04:20 PM

Quote:

Originally Posted by Staubsauger17

E-mail sent to ACS! Awaiting response.

Response received - Order confirmed!

7LitreC5 · 11-12-2018, 04:22 PM

Received mine too. Nice looking product for sure.

Quote:

Originally Posted by DANACO

Received mine this morning

99BLKBRD · 11-12-2018, 04:40 PM

Email sent, waiting on reply.

99BLKBRD · 11-12-2018, 05:23 PM

Ordered.

meSSohappy · 11-12-2018, 07:19 PM

List updated.

Please check list to see if info is correct.

Stealth7 · 11-12-2018, 08:57 PM

Does installation of the fronts or the rears require drilling new holes or does it used existing holes with the same or different hardware?

Thank you for your responses!

DBelcher · 11-12-2018, 09:28 PM

Email sent, reply received, and ordered!

DANACO · 11-12-2018, 10:22 PM

Quote:

Originally Posted by Stealth7

Does installation of the fronts or the rears require drilling new holes or does it used existing holes with the same or different hardware?

Thank you for your responses!

To their instructions, you stick the guards in place with the attached strip of VHB tape (3M) then drill holes in the wheel well liner using the holes in the guards as a guide. There are three split rivets that go in the holes for a permanent installation. I’m not too keen on the “permanent “ install aspect of the rivets.

I will look at alternatives that allow me to more easily remove them at will. Perhaps wel nuts, threaded crush inserts or most likely tinnerman nuts as they are very flat and won’t raise the guards off the liner enough to make any difference in fit and will be very secure, even more so than their rivets, they will just require a small slit in the liner where they’ll slip in.

meSSohappy · 11-19-2018, 12:54 PM

Anyone else ready to order fronts? Lets get this done !!

FNxR3DNECK · 11-19-2018, 01:32 PM

Quote:

Originally Posted by meSSohappy

Anyone else ready to order fronts? Lets get this done !!

I have the OEM ZL1 rockers on my SS 1LE, I'm going to email them to get a set of fronts though I don't need the rears.

Torquem · 11-19-2018, 02:36 PM

Received my fronts today

waterman · 11-19-2018, 02:55 PM

Quote:

Originally Posted by DANACO

To their instructions, you stick the guards in place with the attached strip of VHB tape (3M) then drill holes in the wheel well liner using the holes in the guards as a guide. There are three split rivets that go in the holes for a permanent installation. I’m not too keen on the “permanent “ install aspect of the rivets.

I will look at alternatives that allow me to more easily remove them at will. Perhaps wel nuts, threaded crush inserts or most likely tinnerman nuts as they are very flat and won’t raise the guards off the liner enough to make any difference in fit and will be very secure, even more so than their rivets, they will just require a small slit in the liner where they’ll slip in.

I found a small rock chip in my passenger side door this past weekend.

It was inevitable with these sticky shoes.

DANACO, Great ideas on fittment, thanks. I'm interested in your opinions on the alternative fitment option that you have chosen. Can you post a pic or two?

Thanks in advance.

11-12-2018, 03:58 PM	#212
Staubsauger17 Wisconsin Camaro Pres. Drives: '17 Camaro ZL1 Join Date: Feb 2017 Location: East Troy, WI Posts: 55	E-mail sent to ACS! Awaiting response. __________________ '17 Hyper Blue Metallic Camaro ZL1 Coupe

11-12-2018, 09:28 PM	#219
DBelcher Drives: 2018 Camaro ZL1 G7Q Join Date: Dec 2016 Location: Fort Huachuca, AZ Posts: 25	Email sent, reply received, and ordered! __________________ “Only two defining forces have ever offered to die for you; Jesus Christ and the American Soldier. One died for your soul; the other for your freedom.” author unknown

11-19-2018, 12:54 PM	#221
meSSohappy Drives: 2018 ZL1 A10 Join Date: May 2012 Location: British Columbia, Canada Posts: 1,372	Anyone else ready to order fronts? Lets get this done !! __________________ DAVENPORT STAGE 2 PLUS - 2" ARH ceramic coated headers - 3" ARH catless exhaust - Stock NPP mufflers - Kong ported SC - Katech 103 ported TB - Rotofab 5" Big gulp CAI - 22.5% lower pulley - ATI Harmonic balancer - Cordes SC expansion tank - MSD hi temp ignition wires - Koolsox spark plug insulators - custom tunes - 660hp/725tq pump - 713hp/763tq race

11-19-2018, 02:36 PM	#223
Torquem Bannable Drives: 2017 Camaro ZL1 Join Date: Oct 2009 Location: Houston, TX Posts: 460 View My Garage	Received my fronts today __________________ One must forego the self to attain total spiritual creaminess, and avoid the chewy chunks of degradation 2017 ZL1 A10 - Hyper Blue Metallic Rotofab CAI, TM ported TB, AWE non res touring catback with PLP's

11-12-2018, 02:29 PM	#211
DANACO Drives: 18 ZL1 Join Date: May 2018 Location: Denver Posts: 220 View My Garage	Received mine this morning

11-12-2018, 04:40 PM	#215
99BLKBRD Drives: 2018 ZL1 Mosaic Black A10 Join Date: Jun 2018 Location: Alabama Posts: 34	Email sent, waiting on reply.

11-12-2018, 05:23 PM	#216
99BLKBRD Drives: 2018 ZL1 Mosaic Black A10 Join Date: Jun 2018 Location: Alabama Posts: 34	Ordered.

11-12-2018, 08:57 PM	#218
Stealth7 Drives: Gen V Viper GTS Join Date: Jan 2018 Location: SoCal Posts: 260	Does installation of the fronts or the rears require drilling new holes or does it used existing holes with the same or different hardware? Thank you for your responses!

User Name		Remember Me?
Password