[aa406079]

So I was hoping for ...

Black hood

Black roof

Black spoiler

Black sharkfin

Blacked out bow tie

Black side mirrors ( leaving the side mirror stems yellow)

Single thick yellow stripe that starts at the front of hood edge and continues up across the roof ( as thick as the roof "valley")


Limo tinted side windows

Black front LPO Splitter

Dark carbon / dark gunmetal 5th gen 1LE wheels

Extra credit... Size appropriate Decepticon symbol replacing the Chevy bow tie :3

[aa406079]

Alternative scheme:


Using same pic as above instead of blacked out hood and roof,

Double black racing stripes that are the same thickness and placement as the Shelby 350

With hash marks on side fronts like this

Perhaps too busy, but photo shop is a good way to find out....








Example of hash marks

[chrisvr6]

[i_see_st4irs]

Hey can someone please take this hyper blue Camaro and put the factory black center stripe on it, make the bowtie black, and put these rims on the car? thanks so much

[chrisvr6]

[i_see_st4irs]

Originally Posted by chrisvr6

Ooh yes thanks so much Chris

[aa406079]

SO THIS IMAGE ...




but i want to add the yellow on the engine hump only....

kind of like an arrow head tapering in the same manner as the front nose of the car....



like this ( the colors are reversed in this example)

[rdowty]

Originally Posted by chrisvr6

you can have more

Thanks. I appreciate it.

[chrisvr6]

[aa406079]

Thanks again to Chris!



so using this image....




I want to put a side stripe near the door to accentuate the black n' yellow theme...



while I like the Camaro Perforance Concept.... I think a curving decal would look best because it will mirror the blacked out side windows....

how the side windows curve down in front and then curve up at the back...

so I want the front of the door stripe to follow the downwards curve of the door contours to end at a point just shy of the bottom of the front wheel arch (while still leaving the bottom line of yellow to preserved the yellow car outline), while the back end of the stripe should curve up to fill in the natural upwards contour of the side profile

The curve at the front follows the natural curve which start above the contour line... meaning half of the curve is still yellow, transitioning to black below that line.

The curve at the back will mirror the curve above the line, ending like a spear point , with the top half yellow and the bottom half black.

Too many words and not enough diagrams... I hope I have been clear...

TO clarify, there should be a little bit of curving decal just AFTER the door frame to curve up to a point where the straight pronounced door countour line ends....


rear should have this curve ( with straight edge)

front should be this curved point rotated 180*




also at the back.... I wanted another stripe on the side bumper that start with a curve following the rear wheel well ( leaving some yellow there) and ending just before the end of the side bumper ( again leaving a borderof yellow to keep the yellow silhouette)

Blacked out mirrors while keeping the stalks yellow to keep the black silhouette of the windows intact.

Blacked out sharkfin.

Heavy tinted tail lights


Thanks again, I think this will be my final draft before going to the detailers with this....

[chrisvr6]

you can try it here and do a sketch how it should look like, because i dont know what you mean

https://pixlr.com/editor/

[aa406079]

this one



with a black stripe matching / continuing the hood stripe on the middle roof valley instead of an all black roof

[aa406079]

Originally Posted by chrisvr6

you can try it here and do a sketch how it should look like, because i dont know what you mean

https://pixlr.com/editor/

heres my crappy attempt.... i messed up the front of the door stripe, its a bit too long and should be touching the wheel well please add double hash marks on thicker than other ( doesnt matter which)

the rear bumper stripe i made a bit too thick at bottom

[Techn9cian805]

can someone make hood vents redhot like the rest of the car?