Chevrolet Corvette Stingray C7 Forum - View Single Post - First C7 HUD install, Warning Graphic Photos!

Andrew6 · 10-28-2013, 01:40 AM

I put a bit of a warning up because most will never want to see their car like this. I spent a good part of yesterday and a little bit of today to tear down, create a temp. fix and put back together.

Now there is some good and alot of bad that will come along with this.

First things first, This is no where near as simple of an install as the c6 was and I don't ever forsee there being a "cheat" to bypass this either. So I'll start with saying that you will have to remove the entire dash(worse than even doing a camaro) to even get to the HUD projector location. Thats not really the bad part. The bad part is the dash that comes with a 1LT is not the same as a 2LT or 3LT. There is not a simple pop out like c6 had or even perforations like the c5 had.

Here is the low down, I had to actually take measurements and use a drimmel to cut out the hole for the projector to project through. I then had to devise a bezel. With there being a different dash for the 2lt and up I ended up using a highly modified c6 dash bezel to hide the cut hole and still give it a decent appearance. This is a temp. fix until I can make a nice looking bezel or price of dashes come down.

So pricing break downs for those wanting HUD from a 1LT standpoint:
HUD projector: Around $500
HUD switch: around $30
Dash if not cutting: Around $800+ shipping (freight)
Harness: I can't give the cost on that as I'm still working on it and there are 2 harnesses instead of the 1 for the c6
Labor: There is alot of labor to this. I had the Dash completely out in around 3 hours with out ever doing it before. It took me 4 times as long to put it back together because it's like a puzzle and if you don't put the right pieces back in the right order they won't fit right and you'll have to take apart ...

Here are some photos of the build, destroy, modify and Fix.

10-28-2013, 01:40 AM	#1
Andrew6 TheDoubleAA.com Drives: 2008 Corvette Coupe ZHZ 269of500 Join Date: Aug 2011 Location: League City Texas Posts: 185	First C7 HUD install, Warning Graphic Photos! I put a bit of a warning up because most will never want to see their car like this. I spent a good part of yesterday and a little bit of today to tear down, create a temp. fix and put back together. Now there is some good and alot of bad that will come along with this. First things first, This is no where near as simple of an install as the c6 was and I don't ever forsee there being a "cheat" to bypass this either. So I'll start with saying that you will have to remove the entire dash(worse than even doing a camaro) to even get to the HUD projector location. Thats not really the bad part. The bad part is the dash that comes with a 1LT is not the same as a 2LT or 3LT. There is not a simple pop out like c6 had or even perforations like the c5 had. Here is the low down, I had to actually take measurements and use a drimmel to cut out the hole for the projector to project through. I then had to devise a bezel. With there being a different dash for the 2lt and up I ended up using a highly modified c6 dash bezel to hide the cut hole and still give it a decent appearance. This is a temp. fix until I can make a nice looking bezel or price of dashes come down. So pricing break downs for those wanting HUD from a 1LT standpoint: HUD projector: Around $500 HUD switch: around $30 Dash if not cutting: Around $800+ shipping (freight) Harness: I can't give the cost on that as I'm still working on it and there are 2 harnesses instead of the 1 for the c6 Labor: There is alot of labor to this. I had the Dash completely out in around 3 hours with out ever doing it before. It took me 4 times as long to put it back together because it's like a puzzle and if you don't put the right pieces back in the right order they won't fit right and you'll have to take apart ... Here are some photos of the build, destroy, modify and Fix.