The 2014 Corvette Stingray Forum
News / Blog Register Community Calendar Today's Posts Search

Go Back   Chevrolet Corvette Stingray C7 Forum > Search Forums
Reload this Page Search Results

Page 1 of 17 1 234511 Last »
Showing results 1 to 30 of 500
Search took 0.06 seconds. Search: Posts Made By: CamaroCracka
Forum: 5th Gen Camaro SS LS LT General Discussions Yesterday, 10:08 AM
Replies: 22
Views: 1,153
Posted By CamaroCracka
I pull the passenger fender liner to get to the...

I pull the passenger fender liner to get to the bolts and take it out the top, but I don't read the manual either. I also have turbo crap in the way so...

From what I understand the ball valves GM...
Forum: 5th Gen Camaro SS LS LT General Discussions Yesterday, 10:03 AM
Replies: 8
Views: 287
Posted By CamaroCracka
I run M&H slicks and when called before buying,...

I run M&H slicks and when called before buying, the guy was very chatty so maybe a call to M&H...
Forum: Camaro ZL1 Forum - ZL1 Specific Topics Yesterday, 09:56 AM
Replies: 12
Views: 460
Posted By CamaroCracka
The cooler is inside the diff and sealed off from...

The cooler is inside the diff and sealed off from the diff fluid. It takes "overcooled" (GMs words not mine) fluid from the radiator trans cooler and runs it through the diff cooler to drop the 300+...
Forum: 5th Gen Camaro SS LS LT General Discussions Yesterday, 09:42 AM
Replies: 14
Views: 621
Posted By CamaroCracka
Thanks I ran a 335 on an 18 with 56...

Thanks



I ran a 335 on an 18 with 56 offset using a 5mm spacer and it barely rubbed the liner, assuming you gain half an inch without the liner, that still only puts you at 355-360. I suppose...
Forum: 5th Gen Camaro SS LS LT General Discussions 05-14-2024, 06:33 AM
Replies: 14
Views: 621
Posted By CamaroCracka
I saw that, but I don't see how that works. Even...

I saw that, but I don't see how that works. Even removing the wheel liner would not get you past the frame rail unless you back halved the car.
Forum: 5th Gen Camaro SS LS LT General Discussions 05-13-2024, 03:04 PM
Replies: 14
Views: 621
Posted By CamaroCracka
Here you go.

Here you go.
Forum: Camaro ZL1 Forum - ZL1 Specific Topics 05-13-2024, 03:01 PM
Replies: 12
Views: 460
Posted By CamaroCracka
ZL1s have a cooler in the diff that is fed trans...

ZL1s have a cooler in the diff that is fed trans fluid from the trans. Fluid runs from the radiator to the cooler in the diff and from the diff cooler to the drivers side of the trans. It is used to...
Forum: Suspension / Brakes / Chassis 05-12-2024, 09:09 AM
Replies: 3
Views: 199
Posted By CamaroCracka
Goodridge makes all kinds of brake lines, several...

Goodridge makes all kinds of brake lines, several specific to Gen5s. I'm sure there is probably some company out there that sells more expensive, maybe even marginally better, but if track guys run...
Forum: Camaro ZL1 Forum - ZL1 Specific Topics 05-12-2024, 08:56 AM
Replies: 12
Views: 460
Posted By CamaroCracka
It would take a lot of trans fluid leaking into...

It would take a lot of trans fluid leaking into the diff to make the gear oil redish. Your diff would have to be overfull. Pull the fill plug to see if it's overfull and compare the color of the diff...
Forum: 5th Gen Camaro SS LS LT General Discussions 05-09-2024, 09:27 AM
Replies: 14
Views: 621
Posted By CamaroCracka
That sort of scoop is better for trying to force...

That sort of scoop is better for trying to force air into the intake, but you have to figure out how to seal it up as there is already under hood pressure at speed so it would not likely do much.
...
Forum: 5th Gen Camaro SS LS LT General Discussions 05-08-2024, 06:40 AM
Replies: 1
Views: 192
Posted By CamaroCracka
Putting the bottom seat cover is not that...

Putting the bottom seat cover is not that difficult. I did it as the first upholstery project I ever tried with a pair of Amazon hog ring pliers and it looked factory when done. Pretty sure there is...
Forum: 5th Gen Camaro SS LS LT General Discussions 05-06-2024, 12:15 PM
Replies: 4
Views: 289
Posted By CamaroCracka
NPP uses a vacuum actuated valve to open a more...

NPP uses a vacuum actuated valve to open a more free flowing side of the muffler like a cutout does. I think most guys, when modifying an exhaust just use cutouts. GM did not invent the cutout valve,...
Forum: 5th Gen Camaro SS LS LT General Discussions 05-06-2024, 09:15 AM
Replies: 5
Views: 307
Posted By CamaroCracka
You can also build it with some nylon fuel line,...

You can also build it with some nylon fuel line, but it takes a good bit of patience. You can get the bends done with a heat gun or boiling water. Boiling water is the safer but more difficult...
Forum: Mechanical Maintenance: Break-in / Oil & Fluids / Servicing 05-01-2024, 07:22 PM
Replies: 13
Views: 773
Posted By CamaroCracka
Now that you mention it, I think I used masking...

Now that you mention it, I think I used masking tape before I took the hood off.
Forum: Forced Induction - V8 05-01-2024, 08:22 AM
Replies: 14
Views: 663
Posted By CamaroCracka
Meth or E85, if you are putting down 700+ at 7...

Meth or E85, if you are putting down 700+ at 7 lbs, add one and increase the boost. You will definitely make more power and should not be at risk at higher boost levels. E85 will cost more because...
Forum: Mechanical Maintenance: Break-in / Oil & Fluids / Servicing 04-29-2024, 04:43 PM
Replies: 13
Views: 773
Posted By CamaroCracka
I must be getting lucky with the hood alignment...

I must be getting lucky with the hood alignment as this is the first I heard of the hole drilling trick. Never needed more than a couple adjustments. I made my daughter help me on the vert since she...
Forum: Forced Induction - V8 04-29-2024, 04:33 PM
Replies: 14
Views: 663
Posted By CamaroCracka
Agree with Tartaglia, if meth added 100hp...

Agree with Tartaglia, if meth added 100hp everyone would run it. You also don't need multi-stage, just use a progressive controller with a solenoid. You can run as many jets as you like.

If you...
Forum: Camaro 1LE Forum 04-29-2024, 04:20 PM
Replies: 8
Views: 3,076
Posted By CamaroCracka
Looks like RockAuto still has some right side Z28...

Looks like RockAuto still has some right side Z28 axles, but I have not seen any 1LE axles for a while. Pretty sure GM discontinued them.
Forum: Forced Induction - V8 04-26-2024, 01:40 PM
Replies: 14
Views: 663
Posted By CamaroCracka
To be on the safe side, a lot of people only run...

To be on the safe side, a lot of people only run meth as insurance. In other words, they don't make the tune dependent on the additional "octane" it provides. Of course, then you leave a lot of the...
Forum: ZL1 Wheels/Tires 04-25-2024, 08:53 AM
Replies: 2
Views: 292
Posted By CamaroCracka
Same as SS 14mx1.5.

Same as SS 14mx1.5.
Forum: Camaro Issues / Problems | Warranty Discussions | TSB and Recalls 04-23-2024, 07:16 AM
Replies: 3
Views: 329
Posted By CamaroCracka
a compressor can be failing and still deliver...

a compressor can be failing and still deliver cold air. You would have to connect some gauges and see what the high and low pressures are.

I had to replace the compressor on my turbo car because...
Forum: Mechanical Maintenance: Break-in / Oil & Fluids / Servicing 04-23-2024, 06:54 AM
Replies: 13
Views: 773
Posted By CamaroCracka
I've done it multiple times. Get some fender...

I've done it multiple times. Get some fender covers so you can lay the condenser on the passenger side without fear of scratching the paint. You can even leave the trans hooked up but you will need...
Forum: 5th Gen Camaro SS LS LT General Discussions 04-23-2024, 06:40 AM
Replies: 7
Views: 578
Posted By CamaroCracka
You have to do the cost benefit analysis for...

You have to do the cost benefit analysis for yourself. Anyone running boost can see big benefits by running e85. For those not running boost, my rule of thumb would be if the use of race fuel would...
Forum: Forced Induction - V8 04-22-2024, 11:31 AM
Replies: 14
Views: 663
Posted By CamaroCracka
I ran meth until I went e85. The nylon lines and...

I ran meth until I went e85. The nylon lines and fittings tend to leak over time and reassembly when your working on the car. Never had a problem with the Snow pump, but their controller died and...
Forum: 5th Gen Camaro SS LS LT General Discussions 04-21-2024, 03:01 PM
Replies: 2
Views: 392
Posted By CamaroCracka
I had an Ideal Garage master cylinder and ended...

I had an Ideal Garage master cylinder and ended up going back to OEM because it was leaking internally. All the clutch issues I've had on both cars in relation to pedal not coming back were fixed...
Forum: 5th Gen Camaro SS LS LT General Discussions 04-18-2024, 07:57 AM
Replies: 6
Views: 481
Posted By CamaroCracka
You would have to turn it hard enough for the...

You would have to turn it hard enough for the carrier's internal clutches to slip.
Forum: Forced Induction - V8 04-17-2024, 06:53 AM
Replies: 14
Views: 722
Posted By CamaroCracka
I don't run a shield on my heater lines and the...

I don't run a shield on my heater lines and the passenger side header even burnt the foam off the aluminum line. I do tuck a lot behind the heat shield that runs up from the trans tunnel and covers...
Forum: Camaro ZL1 Forum - ZL1 Specific Topics 04-17-2024, 06:48 AM
Replies: 8
Views: 789
Posted By CamaroCracka
All manufacturers eventually discontinue all...

All manufacturers eventually discontinue all parts. If you want to race old iron, you either need to invest in a stock of used parts or buy replacements from the aftermarket. DSSVs were over a grand...
Forum: 5th Gen Camaro SS LS LT General Discussions 04-16-2024, 02:24 PM
Replies: 12
Views: 665
Posted By CamaroCracka
Summit has a 415 short block for $4200, $6200 for...

Summit has a 415 short block for $4200, $6200 for GM LS3 long block. When my vert spun a rod I had a 416 built for 7k and installed for another thousand. That included a new clutch and a cam swap.
...
Forum: 5th Gen Camaro SS LS LT General Discussions 04-16-2024, 02:09 PM
Replies: 11
Views: 565
Posted By CamaroCracka
Looks like the Spohn brace with the two...

Looks like the Spohn brace with the two additional sides to make a triangle. It might be good if you wanted to cut out the cross member to remove the oil pan and not replace it. One guy did that with...
Showing results 1 to 30 of 500
Page 1 of 17 1 234511 Last »

 
Forum Jump

All times are GMT -5. The time now is 01:04 AM.

Contact Us - Chevrolet Corvette Stingray C7 Forum - Archive - Privacy Statement - Terms of Service / DMCA Policy - Top

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.