Chevrolet Corvette Stingray C7 Forum

		Chevrolet Corvette Stingray C7 Forum > Search Forums
Search Results

Page 1 of 15

Last »

Showing results 1 to 30 of 421
Search took 0.03 seconds. Search: Posts Made By: eimarshall

Forum: Member Car Journals

10-21-2025, 04:05 PM

Replies: 55

The Evolution of EMarshall's CamAERO

Views: 30,572

Posted By eimarshall

Just thought I'd drop in and share an fun video....

Just thought I'd drop in and share an fun video. :-P

https://youtu.be/e-wPTLtIspQ?si=AHhnmDY_achMZ8dT

Forum: Wheels / Tires

09-24-2025, 04:04 PM

Replies: 9

4-tires off 2023 zl1-1le

Views: 1,479

Posted By eimarshall

Are you sure you won't ship? I'd pay....

Are you sure you won't ship? I'd pay....

Forum: Road Course/Track and Autocross

09-10-2025, 01:51 PM

Replies: 33

Aero Discussion (Again)

Views: 4,152

Posted By eimarshall

Nice work! For adjusting the height on the...

Nice work!

For adjusting the height on the QR mounts, you could just put shims/washers under the brackets that mount to the splitter. Move the frame mounts to the highest setting you could...

Forum: Road Course/Track and Autocross

04-09-2025, 04:03 PM

Replies: 4

Front suspension feel weird

Views: 1,447

Posted By eimarshall

Double check your toe rods. I had the bolt on the...

Double check your toe rods. I had the bolt on the knuckle end loosen up a bit. That caused just enough wiggle to induce an oscillation during sustained cornering. If you just had an alignment they...

Forum: Road Course/Track and Autocross

03-12-2025, 03:05 PM

Replies: 42

Suspension setup, track only car

Views: 12,526

Posted By eimarshall

I got a screaming deal on a Katech C7 GS.... :-) ...

I got a screaming deal on a Katech C7 GS.... :-)

I have yet to actually make the tunnels but these are the molds. I split them into inner and outer tunnels.

The outer tunnels are similar to AJ...

Forum: Road Course/Track and Autocross

03-11-2025, 03:47 PM

Replies: 42

Suspension setup, track only car

Views: 12,526

Posted By eimarshall

I designed and made the tunnel molds but never...

I designed and made the tunnel molds but never got a chance to put them on my car before I sold it. They are just collecting dust now.

Forum: Road Course/Track and Autocross

03-10-2025, 07:27 PM

Replies: 42

Suspension setup, track only car

Views: 12,526

Posted By eimarshall

Breaking something is just an excuse to make it...

Breaking something is just an excuse to make it better!!

I think AJ Hartman mentioned in a video that running the splitter between 3-4" off the ground gives pretty optimal results. Lower will net...

Forum: Wheels | Tires -- Sponsored by The Tire Rack

12-26-2024, 05:23 PM

Replies: 4

Wheel spacer and axle bearings

Views: 2,559

Posted By eimarshall

I have run 1inch spacers on track for a couple...

I have run 1inch spacers on track for a couple years with no issues. The bearing issue arises from inappropriate wheel offset and leverage on the hub.

Forum: Exterior Parts & Accessories

12-25-2024, 06:49 PM

Replies: 4

Splitter Tunnel Molds

Views: 4,273

Posted By eimarshall

Here are some pics of the rough molds. I designed...

Here are some pics of the rough molds. I designed the inner mold to fit under the angled aux radiator while still providing maximum volume and around a 10 degree slope in the fore-aft direction.
...

Forum: Exterior Parts & Accessories

12-24-2024, 02:10 PM

Replies: 4

Splitter Tunnel Molds

Views: 4,273

Posted By eimarshall

Splitter Tunnel Molds

I made a set of molds to make splitter tunnels out of carbon fiber. I designed them to work fit under the aux radiators. One inner and one outer tunnel for each side. The resulting tunnels would mate...