HELP! wrong screws for door panel??! - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

TwentyTen2SSRS · 08-05-2013, 10:21 PM

I bought these I swear it's what I read on a thread from here?

Anyways it seems the top were just too small and wouldn't hold trim down. Did I get the wrong ones?

Sent from my iPhone using Tapatalk 2

TwentyTen2SSRS · 08-05-2013, 10:23 PM

Does anyone have a link to the right ones to buy?

Sent from my iPhone using Tapatalk 2

TwentyTen2SSRS · 08-05-2013, 11:17 PM

Bump please!

BIO-HAZARD · 08-05-2013, 11:32 PM

Try the same size in a Truss Head , or use a washer .If the screw isn't holding in the hole you might have to go one size bigger. I had to make to trips to the hardware store myself...Good luck

TwentyTen2SSRS · 08-05-2013, 11:45 PM

Quote:

Originally Posted by Figjam-5

Try the same size in a Truss Head , or use a washer .If the screw isn't holding in the hole you might have to go one size bigger. I had to make to trips to the hardware store myself...Good luck

Perfect. It screwed in perfectly tight I'm guessing the head on it was just not big enough to lock down the label so holes from panel popped out. I'll look for truss heads

BIO-HAZARD · 08-06-2013, 10:21 AM

Hey Just find a real thin washer , or a rubber washer to put on each screw , I remember I couldn't find any Truss Heads with out a point . if you use a pointed screw it could go through the panel so you would have to snip the point off okay ...I ended up using washers on mine Lock ones work well...hope this helps .

TwentyTen2SSRS · 08-06-2013, 11:14 AM

Quote:

Originally Posted by Figjam-5

Hey Just find a real thin washer , or a rubber washer to put on each screw , I remember I couldn't find any Truss Heads with out a point . if you use a pointed screw it could go through the panel so you would have to snip the point off okay ...I ended up using washers on mine Lock ones work well...hope this helps .

Yeah that sounds perfect. Ill look for some washers today. I made a mistake on one spot and have a small indent as if screw was going to pop through luckily I caught it I'm time!

Sent from my iPhone using Tapatalk 2

TwentyTen2SSRS · 08-06-2013, 11:19 AM

Is this the replacement for the inner part of the door? http://store.gmpartshouse.com/parts/...=Outer%20panel

13blackLS · 08-06-2013, 12:34 PM

That looks like the outer door skin?

Are you looking for the panel that you vinyl covered blue?

http://store.gmpartshouse.com/parts/...agramCallOut=1

TwentyTen2SSRS · 08-06-2013, 01:14 PM

Quote:

Originally Posted by 13blackLS

That looks like the outer door skin?

Are you looking for the panel that you vinyl covered blue?

http://store.gmpartshouse.com/parts/...agramCallOut=1

No I'm looking for the inner for panel that surrounds the part I painted blue

Sent from my iPhone using Tapatalk 2

13blackLS · 08-06-2013, 02:48 PM

The link i posted is for the entire panel...just look at the options cause some are with abl..some are for premium sound...etc....see which one is for basic door panel...i dont think you can order the surrounding part alone....i could be wrong though

08-05-2013, 10:21 PM	#1
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,972 View My Garage	HELP! wrong screws for door panel??! I bought these I swear it's what I read on a thread from here? Anyways it seems the top were just too small and wouldn't hold trim down. Did I get the wrong ones? Sent from my iPhone using Tapatalk 2 __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

08-05-2013, 10:23 PM	#2
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,972 View My Garage	Does anyone have a link to the right ones to buy? Sent from my iPhone using Tapatalk 2 __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

08-05-2013, 11:17 PM	#3
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,972 View My Garage	Bump please! __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

08-05-2013, 11:32 PM	#4
BIO-HAZARD INFECTED Drives: 2011 1LT Synergy Green Join Date: May 2011 Location: Upstate PA Posts: 3,226	Try the same size in a Truss Head , or use a washer .If the screw isn't holding in the hole you might have to go one size bigger. I had to make to trips to the hardware store myself...Good luck __________________ http://www.camaro5.com/forums/showthread.php?t=485533

08-06-2013, 10:21 AM	#6
BIO-HAZARD INFECTED Drives: 2011 1LT Synergy Green Join Date: May 2011 Location: Upstate PA Posts: 3,226	Hey Just find a real thin washer , or a rubber washer to put on each screw , I remember I couldn't find any Truss Heads with out a point . if you use a pointed screw it could go through the panel so you would have to snip the point off okay ...I ended up using washers on mine Lock ones work well...hope this helps . __________________ http://www.camaro5.com/forums/showthread.php?t=485533

08-06-2013, 11:19 AM	#8
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,972 View My Garage	Is this the replacement for the inner part of the door? http://store.gmpartshouse.com/parts/...=Outer%20panel __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

08-06-2013, 12:34 PM	#9
13blackLS Drives: 2013 camaro ls; 2005 rx8 Join Date: Mar 2013 Location: Houston Posts: 577	That looks like the outer door skin? Are you looking for the panel that you vinyl covered blue? http://store.gmpartshouse.com/parts/...agramCallOut=1

08-06-2013, 02:48 PM	#11
13blackLS Drives: 2013 camaro ls; 2005 rx8 Join Date: Mar 2013 Location: Houston Posts: 577	The link i posted is for the entire panel...just look at the options cause some are with abl..some are for premium sound...etc....see which one is for basic door panel...i dont think you can order the surrounding part alone....i could be wrong though