03-15-2017, 07:50 PM | #43 |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
Mine is scheduled for delivery tomorrow
Sent from my iPad using Tapatalk
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
03-15-2017, 07:58 PM | #44 |
__________________
2011 2SS/RS Convertible, Victory Red, Roto-Fab CAI, Stainless Power 1 7/8 headers, No Cats, Straight piped, Bo White TB, ZL1 CONVERSION, CDC Roll bar and some powder coating and dipping.
|
|
03-16-2017, 04:15 PM | #45 |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
Ryan B.
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
03-16-2017, 06:56 PM | #46 |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
I am liking it Few issues though Only 2 of the holes lined up :( modified to get it to work Paint is ok has some marks/swirls tried. Y hand to remove Honestly 9/10 people would never notice. Kinda drives me crazy we will see how it is in the sun. 7/10 due to the fit and finish Ryan B.
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
03-16-2017, 08:56 PM | #47 |
Drives: 2013 SS Camaro Join Date: May 2016
Location: Chicagoland area
Posts: 223
|
Looks GOOD...so u had to drill 2 new holes?..is the middle taillight visible from the rear?
Sent from my SM-N920P using Tapatalk |
03-16-2017, 09:13 PM | #48 | |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
10-13 with Z/28 Style Spoiler
Quote:
No I didn't drill the rear deck. I used a sheet metal screw to go into the bottom of the rear spoiler. It had a pretty good bite. I also laid down some 3m tape on the trunk lid before installing for some extra hold As far as the light certain angles it is visible. If you have a super low car I am not sure. If you tailgate super close to it may be hard to see? Definitely a higher vehicle (truck/SUV) can see it. I think it will be fine Ryan B.
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
|
03-16-2017, 10:21 PM | #49 |
Did you have to use 3M tape or will it be fine without?
I was hoping for a factory fit with just the five bolts. Are the factory studs in place on the new spoiler?
__________________
2011 2SS/RS Convertible, Victory Red, Roto-Fab CAI, Stainless Power 1 7/8 headers, No Cats, Straight piped, Bo White TB, ZL1 CONVERSION, CDC Roll bar and some powder coating and dipping.
|
|
03-16-2017, 11:03 PM | #50 | |
|
Quote:
What pretty much everyone does is widen the factory holes a little in whichever direction is needed to get the spoiler to fit correctly. Once you have the spoiler fitted and centered on your trunk, you tighten it down with the included nuts (can't remember if they included washers too). No 3M tape necessary. They do include some single sided foam tape/gasket for cushion/weather-sealing though. EDIT: Sorry guys, not studs with nuts.. Threaded inserts with screws. Ryan refreshed my memory haha. Last edited by cnrad; 03-17-2017 at 10:42 AM. |
|
03-17-2017, 03:47 AM | #51 | |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
Quote:
Do you have a fiberglass or abs version? Mine did not have studs there are threaded inserts (4). With the convertible not all the holes are used I don't think you need to use 3M tape it was just an added security measure imo Ryan B.
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
|
03-17-2017, 10:40 AM | #52 | |
|
Quote:
Also, I had the fiberglass version of the spoiler. I believe they went from 6 down to 4 mounting points on their ABS version of the spoiler, so you might wanna double check and make sure they actually gave you a fiberglass one. Mine had "FG 618" carved onto the underside of the spoiler which is the model number for their fiberglass version. Do you remember seeing anything like that on yours? |
|
03-17-2017, 01:50 PM | #53 |
Drives: 2010 Camaro Join Date: Dec 2009
Location: Montreal, Canada
Posts: 1,254
|
The Original ACS Z/28 Spoiler for the 10-13 Camaro does have the provision for the Convertible Antenna.
Replica's are a cost effective solution, but not manufactured in RTM composite. https://acscomposite.com/collections...spired-spoiler |
03-19-2017, 04:35 PM | #54 |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
Ryan B.
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
03-19-2017, 08:28 PM | #55 |
__________________
2011 2SS/RS Convertible, Victory Red, Roto-Fab CAI, Stainless Power 1 7/8 headers, No Cats, Straight piped, Bo White TB, ZL1 CONVERSION, CDC Roll bar and some powder coating and dipping.
|
|
03-20-2017, 01:50 PM | #56 |
Let's go fishing!
Drives: a car with 8 cylinders Join Date: Apr 2016
Location: Seabrook, Texas
Posts: 1,129
|
Please post more pictures. Would like to see side profile, from the rear, and what it looks like in all those positions with the top down.
Thanks!
__________________
"When choosing between two evils, I always like to try the one I’ve never tried before." Mae West 1892-1980
|
|
|
|
|