07-16-2023, 08:53 AM | #29 | |
Drives: 2017 Nightfall Grey 2SS 6 Speed Join Date: Jan 2022
Location: Wisconsin
Posts: 21
|
Quote:
|
|
07-16-2023, 10:11 AM | #30 |
Drives: 2022 camaro SS 1LE Join Date: Jan 2023
Location: Utah
Posts: 131
|
No need for the LT4 until you want to boost it imho
|
07-22-2023, 09:27 AM | #31 |
Drives: 2017 Nightfall Grey 2SS 6 Speed Join Date: Jan 2022
Location: Wisconsin
Posts: 21
|
Hello so the tuner just got back to me with the build list. This is what they said:
A full cam kit comes with the following: Cam, lifters, liter trays, head gaskets, head bolts, push rods, valve seals, balance springs, valve locks, retainers, valve cover gaskets, timing chain, timing tensioner, cam gear and bolts, front plate cover, oil pump, oil pump o ring, spark plugs, spark plug wires, all front cover gaskets and seals, water pump gaskets, oil pan gasket, balancer bolt, two oil changed with GM racing filters, new antifreeze, valve job and cylinder head surfacing, all the labor, and tuning (I’m sure I’m missing stuff too) is all included in the cost for a cam kit. That cam will not drive completely stock it will have its quirks, but overall it is a very well mannered camshaft. They are referring to the BTR 220 Cam. I believe it is his wife that takes care of the inquiries, not the tuner himself thats why it says "im probably missing some stuff too" Im no expert but it sounds like a good setup.. I am strongly considering it.. Is there anything else i should watch out for? Opinions? By the way I was also told by the stealership a year or 2 ago that my oil pan gasket is leaking ever so slightly and was quoted $1300 to replace it.. so that would get taken care of. |
07-22-2023, 09:55 AM | #32 | |
Drives: 2022 Camaro zl1 Join Date: Jun 2023
Location: Tx
Posts: 54
|
Quote:
|
|
07-23-2023, 03:10 AM | #33 |
Drives: like an old lady Join Date: Jun 2012
Location: indiana
Posts: 2,415
|
i think very minimal gains, if any. idk if there's any direct power to be had with higher fuel pressure. my bolt on 1LE car was seeing an injector pw max of 5.5 ms on e80 with a lambda of .88 - i imagine adding a fair amount of power would push that pw up into the uncomfortable range. i'm no tuner, just sharing info. i would feel much better knowing it would not be near the end capabilities of the fuel system simply for the peace of mind regarding longevity & reliability. it would prob be fine on gasoline.
__________________
2016+ camaro: everyone’s first car
|
07-24-2023, 04:03 PM | #34 |
Drives: '16 2SS M6 Join Date: Aug 2019
Location: Hughes Springs, TX
Posts: 322
|
Tighten all the pan bolts before spending a dime on this oil leak. It's a known issue that the bolts get slightly loose and cause a drip. I tightened mine 3 years ago because of a spot on the garage floor and have not had a drop of oil leak out since.
__________________
David
'16 2SS M6 black on black, SW long tube full exhaust, NPP, Roto-fab CAI, ported stock TB '16 2SS M6 black w/Metallic black stripes, Kalahari, 6 piston front (totaled 1/22/20) '14 Fusion Titanium 2.0T '83 Jeep Wagoneer |
05-24-2024, 04:12 PM | #35 | ||
Drives: '23 LT1 Join Date: Apr 2023
Location: USA
Posts: 33
|
Quote:
Don't suppose you want to drop your playlist? Had me jamming the whole video. |
||
|
|
Post Reply
|
Tags |
btr 220 cam, cam, cam install |
|
|